Radio Interferenge Suppression X2 Capacitor.
SPECIFICATION
ACROSS-THE-LINE AND INTERFERENCE SUPPRESSION CAPACITOR CLASS X2 ----- MPX
1. REFERENCE STANDARDS
UL 1414
CUL
USED FOR ACROSS-THE-LINE CAPACITOR ANTENNA-COUPLING AND LINE-BY-PASS
COMPONENTS FOR 250V.AC. -40℃ TO +85℃
ENEC-VDE 0565-1 EN 132 400(1994)/A2(1998) AND IEC 60384-14Ⅱ(1993)/A1(1995)
USED FOR RADIO INTERFERENCE SUPPRESSION CAPACITOR FOR 275V.AC
-40℃ TO +100℃.
2. RATED VOLTAGE :
250V.AC ( UL 1414 , CSA ) 275V.AC ( IEC 60384-14 )
3. CAPACITANCE RANGE :
0.0047uF TO 1.0uF
4. CAPACITANCE TOLERANCE :
J(±5%) , K(±10%) , M(±20%).
5. DIELECTRIC :
METALLIZED POLYPROPYLENE FILM.
6. DISSIPATION FACTOR (tanδ) :
LESS THAN 0.1% AT 1KHZ AND 20℃.
7. INSULATION RESISTANCE :
BETWEEN ELECTRODES
(1) LESS THAN OR EQUAL TO 0.33uF ≧ 30,000MΩ.
(2) GREATER THAN 0.33uF ≧ 10,000MΩ/uF.
MEASURED AT 100V.DC 60 SEC AND 20℃.
8. WITHSTAND VOLTAGE :
BETWEEN ELECTRODES
APPLIED 1075V.DC FOR 60 SEC. AND 20 ℃ OR 2100V.DC FOR 1 SEC.
9. CLIMATIC CATEGORY : IN ACCORDANCE WITH DIN40040 GMF
G (MINIMUM LIMIT TEMPERATURE) = -40℃.
M(MAXIMUM LIMIT TEMPERATURE) = +100℃.
F (HUMIDITY CATEGORY) = AVERAGE RELATIVE HUMIDITY ≦ 75% , 95% FOR 21
DAYS PER YEAR CONTINUOUSLY ; 85% FOR THE
REMAINING DAYS OCCASIONALLY.
10. OPERATING TEMPERATURE RANGE :
-40℃ TO +85℃(UL1414CSA) , -40℃ TO 100℃(IEC 60384-14).
11. HUMIDITY TEST :
TEST CONDITIONS :
TEST TEMPERATURE : 40℃ ± 2℃.
RELATIVE HUMIDITY : 90 TO 95%.
TEST DURATION : 21 DAYS.
TEST CRITERIA :
(1) CAPACITANCE DRIFT : ≦ ±5% OF THE INITIAL VALUE.
(2) INSULATION RESISTANCE : ≧ 50% OF SPECIFIED VALUE.
12. LIFE TEST :
TEST A :
IN ACCORDANCE WITH VDE 0565-1 , SECTION 5.4.18. AND SS 4430414, SUB-CLAUSE
12.11. CONDITIONS
TEST TEMPERATURE : +100 ± 2℃.
TEST VOLTAGE : 1.25 × RATED VOLTAGE AND 1,000V.AC/50HZ 0.1 SEC.EACH HR
APPLIED.
TEST B:
IN ACCORDANCE WITH UL 1414 PERFORMANCE 10 OR CSA C22.2 NO.1-M1981 6,13,3.
CONDITIONS
TEST TEMPERATURE : +100 ± 3℃.
TEST VOLTAGE : 440V.AC AND 880V.AC/60HZ . 0.1 SEC. EACH HR APPLIED.
TEST DURATION : 1008HRS.
TEST CRITERIA :
(1) CAPACITANCE DRIFT : ≦±10% OF THE INITIAL VALUE.
(2) INSULATION RESISTANCE : ≧ 50% OF SPECIFIED VALUE.
(3) VISUAL INSPECTION : NO DETECTABLE DAMAGE .
13. SOLDERABILITY :
TEST CONDITIONS :
SOLDER BATH TEMPERATURE : 260 ± 5℃.
SOLDER : LEAD FREE SOLDER.
SOLDER TIME : 10 ± 1.0 SEC.
TEST CRITERIA
75% OF THE SURFACE TINNING.
14. VIBRATION RESISTANCE : (JIS 5115)
TEST CONDITIONS :
FREQUENCY CYCLE : 1 MINUTE PER CYCLE 10-55-10 HZ.
TEST DURATION : PERPENDICULAR DIRECTION WITH THE SAME METHOD FOR 45
MINUTES EACH , TOTAL 90 MINUTES.
TEST CRITERIA :
(1) APPEARANCE : NO VISUAL DAMAGE.
(2) CONTACT : NORMAL.
15. TENSILE STRENGTH OF ELECTRODES :
TEST CONDITIONS :
LOAD FORCE : 1.0KGS.
HOLDING TIME : 10 ± 1 SEC.
TEST CRITERIA :
NO WIRE BROKEN AND NO DAMAGE OF THE CAPACITOR.
16. MARKING
CAPACITORS ARE MARKED WITH TYPE IDENTIFICATION , CAPACITANCE
CAPACITANCE TOLERANCE , VOLTAGE AND APPROVED CERTIFICATION MARK.

規格圖友善列印